Product Description
A two-component, pure epoxy resin based self-priming, anti-abrasion coating with excellent resistance to seawater, crude oil, fuel oil and abrasion. Applicable over new or old steel requiring only the removal of loose rust as a surface tolerant coating, curable at low temperature even -18 /-0.4 එ and meets VOC requirements as high solids coating. Approved as a Corrosion Control Coating for water ballast tanks by Lloyd’s Register of Shipping (LR), Germanishier Lloyd (GL), and MARINTEK/DNV. It is in full accordance with the requirements in NORSOK M-501 System No. 3 and No 7. Also approved as a Corrosion Control Coating for water ballast tanks by IMO PSPC rules. Recommended Use As an anti-corrosion and anti-abrasion coating for long-life protection of steel structures in severely corrosive environment such as Underwater hull outside, Boottop, Topside, Exposed parts of ship, Water ballast tank, Cargo holds, etc. As a tank coating for ship’s crude oil tanks, fuel oil tanks and interior of pipe lines transfer crude oils, etc. Applicable to steel structures for offshore projects, plants, bridges and others.
Physical Properties
Finish and Color Flat. Grey (1128, 1151), Mid Buff (3362).
Drying Time Substrate temperature 5 /41 20 /68 30 /86 Set to touch 8 h 1 h 30 min Dry through 16 h 3 h 2 h * The actual drying time is subject to the film thickness, ventilation, humidity etc., and drying time under other temperature conditions should be checked and informed by KCC. Solids by Volume Approx. 72 % (Determined by ISO 3233)
Theoretical Spreading Rate
7.2 ༇/L in 100 ༁ dry film thickness on a smooth surface.
Specific Gravity Approx. 1.50 for Mixture of Base and Curing agent.
Flash Point Base (EH2351-A) : 26 /79 (Closed cup) Curing Agent (EH2351-B) : 26 /79 (Closed cup)
Application Details
Surface Preparation
Remove any oil, grease, dirt and any contaminant from the surface before painting by proper method such as solvent cleaning and fresh water washing, etc. * Steel : Blast cleaning to Sa2.5 or Power tool cleaning to St3, etc.
Application Conditions
The surface should be completely cleaned and dried. Do not apply when relative humidity is above 85 %. The surface temperature should be at least 2.7 (5 එ) above dew point to prevent condensation. In confined areas, ventilate with clean air during application to assist solvent evaporation. Mixing Base (Part A) : Curing Agent (Part B) = 4 : 1 (by volume) Mix thoroughly together prior to application in the proportions with power agitator as delivered. Pot Life 3 h at 20 /68 එ
Preceding Coat Galvany Shopprimer IZ182, Korepox EH2351, or according to specification.
Thinning Thinner No. 024 Do not dilute each components separately, only the mixture.
Disclaimer : The information in this data sheet is believed to the best of our knowledge based on laboratory test and practical experience. However, there are many factors affecting the performance of product and the product quality itself, so we are not able to guarantee without the confirmation of the purpose of using the product from us in writing. We reserve the right to change the data without notice and you should check that this data sheet is current prior to using the product.
KCC Corporation
Korepox EH2351 (Two-Component)
Application Method
Spray (Airless or Air), Roller or Brush application For airless spray application ; Nozzle orifice : 483 ໃ ~ 787 ໃٻ(0.019כ ~ 0.031 )כ Output pressure : 11.7 MPa ~ 15.2 MPa Fan : 60 º (Airless spray data are indicative and subject to adjustment)
Typical Film Thickness
100 ~ 200 ໃ dry. May be specified in another film thickness than indicated depending on purpose and area of use. Recoating Interval At 20 / 68 එ, Minimum : 3 h Maximum ; - Immersion : 15 d - Non-immersion : Free Prior to overcoating, remove the oil, salt, chalking material and any other contaminants on aged coating film completely by proper cleaning method such as solvent cleaning and/or fresh water washing.
Subsequent Coat Korepox EH2351, Korepox EH2351(GF), Korepox Topcoat H.B. ET5740, Korepox Topcoat H.B. ET5745, Korevitar H.B. EH2540, Korepox H.B. EH2560, or according to specification.
Shelf Life 12 months
Heat resistance Continuous : 93 /200 (Non-immersion service) Non-continuous : 121 /250 (Non-immersion service) Chemical Resistance Acids Alkalis Solvents Salts Water Splash & Spillage Good Good Very Good Excellent Excellent
Fumes Very Good Excellent Excellent Excellent Excellent
Immersion Fair Good Good Good Good
Standard Packing Unit
16 L (EH2351-A : 12.8 L, EH2351-B : 3.2 L)
Remarks Do not store at temperature below 5 /41 එ or above 40 /104 එ. Protect skin and eyes from direct contact with liquid paint, and avoid prolonged breathing of solvent vapors. Use with adequate ventilation. Respiratory protection is recommended when applying this product in confined spaces or stagnant air.
Issued April 2009